Foshan Guangteng New Energy Co., Ltd. has been committed to the
development, production, marketing and after-sales service
of heat pump since founded in 2003,
and granted as credit business enterprise by Chinese Government.
Operate at a high effictency,generally cost to operate less than other types of conventional heating systems,save your electricity or gas bills.
Operate with no flames,fumes or flues;Water and electricity isolated.
Produces no carbon emissons.
(4)Easy to Install
Easy to install and don't take up nearly as much room, making them suitable for even the smallest of gardens.
With intelligent control systems which convenient and simple operation.
(6)Constant Hot Water Supply
Provide hot waterno matter in cloudy day,snowy day or at night.
Can be applied to sanitary hot water,house heating,swimming pool and spa pool temperature and so on.
Pool Heat Pump Sketch Map
Introduction With the help of titanium heat exchanger, swimming pool pump transfer heat from air into water by the physical changes of refrigerant.
1. Swimming Pool
4. Heat Pump
5. Water Treatment
A. Ambient Air
C. Fan Motor
D. Cool Air
G. Hot Water Outlet
H. Cool Water Inlet
I. Titanium Heat Exchanger
J. Emercon Expansion Valve
A common auxiliary heater is typically fueled by propane or natural gas, or an air-to-water heat pump. Gas heaters are the most responsive—an appropriately sized heater can reasonably raise the pool temperature 5°F in four hours.
A heat-pump pool heater may take six to eight hours to raise the same pool water 5°F. A properly sized SPH system may require several days. The other trade-offs between these technologies are cost and environmental impact.
As shown by the “Pool Heating Fuels & Costs” table, the most economical method for pool heating is a SPH system. The initial costs of a SPH system are comparable with heat pump and liquid fuel pool heaters, while the operating costs are far less.
The lower cost of SPH systems is due to their simplicity and efficiency. For most SPH systems used for outdoor pools, the only moving part is a motorized valve activated by a differential controller.
The controller uses two sensors—one near the solar pool collectors, where it is exposed to the same solar radiation as the collectors, and one that measures the water temperature from the pool.
When there is enough solar energy available to heat the pool water, the valve is opened. (A common temperature differential is 4°F, although this temperature can be field-set on some controllers.)
The pool water is pumped through the collectors before being returned to the pool.
When the pool reaches the controller’s high temperature setting or there is not sufficient solar radiation to maintain a collector temperature that is 1°F to 2°F more than the pool water,
the motorized valve closes and the mechanical system functions as it would in a pool without a SPH system.
Most solar pool heating systems include the following:
A solar collector -- the device through which pool water is circulated to be heated by the sun
A filter -- removes debris before water is pumped through the collector
A pump -- circulates water through the filter and collector and back to the pool
A flow control valve -- automatic or manual device that diverts pool water through the solar collector.
You'll want a properly sized pool pump for a solar system. If you're replacing a conventional pool heating system with a solar system, you may need a pump larger than your current one or a separate,
smaller pump to move the pool's water to and through the collectors. Here we can provide you air source swimming pool heat pump.
About Our Factory
GuangTeng Solar Energy Electrical Appliance Co., Ltd has been committed to the development, production, marketing and after-sales service of heat pump water heaters since founded in 2003, and granted as credit business enterprise by China Government.
Our factory locates in Shunde,China, with 10000 square meters of production workshop, modern production equipments, experienced management and development teams. We carry out ISO9001 quality control system to ensure that providing top quality products and service to our customers, quality permeate into every detail of products. So far our partners throughout Europe,Australia, Africa, Middle East, South America and etc.
(1)Complying with ISO standard.
(2)Using world famous Compressor i.e. COPLAND, PANASONIC, HITACHI, SANYO.
(3)Complete Inspection covering water system and electricity to ensure stable hot water production.
(4)With high efficiency tube in shell heat exchanger, finned heat exchanger or plate heat exchanger. All heat exchangers with insulation to prevent heat loss.
(5)Evaporator using surface modification of hydrophilic aluminous foil.
(6)Electric Expansion valve with accurate flow control and gas distribution.
(1)Offer OEM service.
(2)Make customized heat pump according to customer's requirement.
(3)Supply spare parts according to order quantity.
(4)General test and operational test carried out for every unit before delivery.
(5)Long warranty period.
Heating at air temperature 24/19℃,water temperature 26/28℃
Heating at air temperature15/12℃,water temperature 26/*℃
Heating at air temperature 7/6℃,water temperature 26/28℃
Heating at air temperature 2/1℃,water temperature 26/*℃